EPOX EP-MVP3C Instrukcja Użytkownika

TRADEMARKAll products and company names are trademarks orregistered trademarks of their respective holders.These specifications are subject to change

Introduction EP-MVP3CPage 1-4Page Left Blank

FeaturesEP-MVP3CPage 2-1Section 2FEATURESEP-MVP3C Features:• Intel Pentium® Processor with MMX technology, AMD K6, Cyrix 6x86MX/MII, idt C6 & Rise

Features EP-MVP3CPage 2-2• Supports ring-in feature (remote power-on through external modem,allows system to be turned on remotely).• Resume by Alarm

InstallationEP-MVP3CPage 3-1Section 3INSTALLATION

Installation EP-MVP3CPage 3-2Figure 1EP-MVP3C Detailed LayoutAGP SLOTPCI Slot #2VIAVT82C598J7WOLJ11IDE1IDE2FDD1DIMM 1DIMM 2Bank 1Bank 0DIMM 3Bank 2PCI

InstallationEP-MVP3CPage 3-3Easy Installation ProcedureThe following must be completed before powering on your new system:3-1. Configure Jumpers3-2. S

Installation EP-MVP3CPage 3-41234ON51WSUPCerocV1234 5NONONOV8.1NONONONOV0.2NOV1.2NOV2.2NONOV3.2NOV4.2NOV8.2NONOV9.2NONOV2.3SW1: CPU Vcore Voltage Sele

InstallationEP-MVP3CPage 3-5Section 3-2System Memory ConfigurationMemory LayoutThe EP-MVP3C supports (3) 168-pin DIMMs (Dual In-line Memory Module).

Installation EP-MVP3CPage 3-6DIMM Module InstallationFigure 3 displays the notch marks and what they should look like on your DIMMmemory module.DIMMs

InstallationEP-MVP3CPage 3-7Figure 4DIMM Module clip before installationFigure 5DIMM Module clip after installationTo remove the DIMM module simply pr

EP-MVP3C

Installation EP-MVP3CPage 3-8Section 3-3Device ConnectorsPlease install the motherboard into the chassis.Now that your motherboard is installed you ar

InstallationEP-MVP3CPage 3-9Section 3-3Device Connectors (continued)J2Speaker - Connect to the system's speaker for beeping1. Speaker 3. GND2. N/

Installation EP-MVP3CPage 3-10Notes:1.Intel ATX version 2.0 specification has recommended you use the power supplywith 0.72A(720mA) in 5.0VSB. With o

BIOSEP-MVP3CPage 4-1Section 4AWARD BIOS SETUPBIOS InstructionsAward’s ROM BIOS provides a built-in Setup program which allows user to modifythe basic

BIOS EP-MVP3CPage 4-2The menu displays all the major selection items. Select the item you need toreconfigure. The selection is made by moving the curs

BIOSEP-MVP3CPage 4-3NOTE: The “Halt On:” field is used to determine when to halt the systemby the BIOS if an error occurs.NOTE: Floppy 3 Mode support

BIOS EP-MVP3CPage 4-4Enabled: Activates automatically when the system boots up causing awarning message to appear when anything attempts to access th

BIOSEP-MVP3CPage 4-5Boot Up Floppy Seek: During Power-On-Self-Test (POST), BIOS will determineif the floppy disk drive installed is 40 or 80 tracks.

BIOS EP-MVP3CPage 4-6Typematic Delay (msec): This setting controls the time between the first and thesecond character displayed by typematic auto-rep

BIOSEP-MVP3CPage 4-7C8000 - CBFFF Shadow:CC000 - CFFFF Shadow:D0000 - D3FFF Shadow:D4000 - D7FFF Shadow:D8000 - DBFFF Shadow:DC000 - DFFFF Shadow:Thes

EP-MVP3CUser NoticeNo part of this product, including the product and software may be reproduced,transmitted, transcribed, stored in a retrieval syste

BIOS EP-MVP3CPage 4-8SDRAM Cycle length: This setting defines the CAS timing parameter of theSDRAM in terms of clocks.The default is 3.2: Provides f

BIOSEP-MVP3CPage 4-94-4 Power Management SetupChoose the “POWER MANAGEMENT SETUP” in the CMOS SETUP UTILITYto display the following screen. This menu

BIOS EP-MVP3CPage 4-10PM controlled APM: This option shows weather or not you want the PowerManagement to be controlled the Advanced Power Management

BIOSEP-MVP3CPage 4-11Suspend Mode: This function works only when the Pentium II Processor isinstalled. The timer starts to count when “System Standb

BIOS EP-MVP3CPage 4-124-5 PNP/PCI ConfigurationThe PNP/PCI configuration program is for the user to modify the PCI/ISA IRQsignals when various PCI/ISA

BIOSEP-MVP3CPage 4-13Reset Configuration Data: This setting allows you to clear ESCD data.The default is DisabledDisabled: Normal Setting.Enabled: If

BIOS EP-MVP3CPage 4-144-6 Load Setup DefaultsThe “LOAD SETUP DEFAULTS” function loads the system default data directlyfrom ROM and initializes the ass

BIOSEP-MVP3CPage 4-15Onchip IDE First Channel: The default value is Enabled.Enabled: Enables Onboard IDE primary port.Disabled: Disables Onboard IDE p

BIOS EP-MVP3CPage 4-16Primary Slave UDMA: This allows you to select the mode of operation for the harddrive.The default is Auto.Auto: The computer wil

BIOSEP-MVP3CPage 4-17COM2: Enable Onboard Serial port 1 and address is 2F8H/IRQ3.COM3: Enable Onboard Serial port 1 and address is 3E8H/IRQ4.COM4: Ena

EP-MVP3CTechnical Support ServicesIf you need additional information, help during installation or normal use of thisproduct, please contact your retai

BIOS EP-MVP3CPage 4-18DMA1: This field selects the routing of DMA1 for the ECP mode.DMA3: This field selects the routing of DMA3 for the ECP mode.Powe

BIOSEP-MVP3CPage 4-19sage and ask for a confirmation.Confirm Password:3. After pressing the [Enter] key (ROM password if the option was not used)or cu

BIOS EP-MVP3CPage 4-20Generic access mode in which neither the BIOS nor the IDE controller will makeany transformations during accessing.The maximum n

BIOSEP-MVP3CPage 4-21INT 12h in order to access the right HDD address!Maximum HDD size:no. Cylinder (1024)x no. Head ( 32)x no. Sector ( 63)x bytes pe

BIOS EP-MVP3CPage 4-22Page Left Blank

AppendixEP-MVP3CA-1Appendix A:A-1 MEMORY MAPAddress Range Size Description[00000-7FFFF] 512K Conventional memory[80000-9FBFF] 127K Extended Convention

Appendix EP-MVP3CA-2[3D0-3DF] CGA adapter.[3F0-3F7] FLOPPY DISK controller.[3F8-3FF] SERIAL port 1.A-3 TIMER & DMA CHANNELS MAPTIMER MAP:TIMER Cha

AppendixEP-MVP3CA-314 Onboard HARD DISK (IDE1) channel.15 Onboard HARD DISK (IDE1) channel.A-5 RTC & CMOS RAM MAPRTC & CMOS:00 Seconds.01 Seco

Appendix EP-MVP3CA-4Page Left Blank

AppendixEP-MVP3CA-5Appendix B:B-1 POST CODESISA POST codes are typically output to I/O port address 80h.POST (hex) DESCRIPTION01-02 Reserved.C0 Turn o

EP-MVP3CTable of ContentsSection 1 IntroductionComponents Checklist ... 1-1OverviewPower-On/Off (Remote) ...

Appendix EP-MVP3CA-60C Initialization of the BIOS Data Area. (40:ON - 40:FF)0D 1. Program some of the Chipset's value according to Setup.(Early

AppendixEP-MVP3CA-73E Try to turn on Level 2 cache.Note: Some chipset may need to turn on the L2 cache in this stage.But usually, the cache is turn o

Appendix EP-MVP3CA-861 1. Try to turn on Level 2 cache.Note: If L2 cache is already turned on in POST 3D, this part will beskipped.2. Set the boot

AppendixEP-MVP3CA-9Appendix CNOTE:The "LOAD SETUP DEFAULTS" function loads the system default data directly from ROM andinitializes the asso

EP-MVP3CSave & Exit Setup ... 4-21Exit Without Saving... 4-21Appendix

IntroductionEP-MVP3CPage 1-1Section 1INTRODUCTIONComponents Checklistüüüüü A. (1) One mainboardüüüüü B. (1) One user’s manualüüüüü C. (1) Floppy ribbo

Introduction EP-MVP3CPage 1-2ATXPOWER SUPPLYEP-MVP3C BoardPower-On/Off (Remote)The EP-MVP3C has a single 20-pin connector for ATX power supplies. For

IntroductionEP-MVP3CPage 1-3Figure 5: System Block DiagramSystem Block DiagramPACPCI Bridgeand memorycontrollerVT82C598VT82C596I/O BridgeSocket 7Proc